CELESTRA
CELESTRA PHOTON SERIES · MONOCHROME

Photon 62M

Full Frame cooled monochrome astronomical camera for high-performance deep-sky imaging.

CELESTRA Photon series camera illustration
Photon family illustration; model-specific connector layout may differ.
61 MP9568 × 6380
3.76 μmPIXEL SIZE
Full FrameSENSOR FORMAT
16-bitADC
Δ40°CTEC COOLING
SENSOR & IMAGING

Monochrome BSI CMOS

Photon 62M combines a Full Frame monochrome sensor with 9568 × 6380 resolution and 3.76 μm pixels. Peak quantum efficiency is >91% and dynamic range is 88.3 dB.

COOLING & STABILITY

Advanced Deep-Sky Platform

Two-stage TEC cooling, a 512 MB DDR3 image buffer, zero amp-glow architecture and integrated anti-dew control support stable long-exposure imaging.

>91%PEAK QE
88.3 dBDYNAMIC RANGE
512 MBDDR3 BUFFER
55.8 fpsMAX RATE · MODE DEPENDENT
17.5/12.5 mmBACK FOCUS
TECHNICAL SPECIFICATIONS

Camera Parameters

The maximum-rate figure is acquisition-mode dependent; it does not specify full-resolution capture at the native ADC bit depth. Backfocus is measured from the selected adapter reference face, so confirm the front-plate and spacer drawing before setting optical spacing. Manufacturer platform reference.

Sensor Monochrome BSI CMOS
Resolution9568 × 6380 (61 MP)
Pixel Size3.76 μm × 3.76 μm
Sensor FormatFull Frame
ADC16-bit
Quantum Efficiency>91%
Dynamic Range88.3 dB
Full Well51 ke⁻ (111 ke⁻ in LCG)
Read Noise2.8–0.97 e⁻ (LCG) / 1.95–0.9 e⁻ (HCG)
INTERFACES & OPERATION

Integration

Power PlanningExternal 12 V DC supply; confirm current capacity for cooling and attached USB accessories
Data InterfaceUSB 3.0 / USB 2.0
Integrated USB Hub4× USB 2.0 + 1× USB 3.0
Maximum Readout Rate55.8 fps at 3184 × 2124, 8-bit, USB 3.0 in the manufacturer reference; confirm enabled mode for the supplied revision
DDR3 Buffer512 MB
CoolingTwo-stage TEC, up to Δ40°C below ambient
Back Focus17.5 / 12.5 mm
Protective Window / SpectrumAR-coated · 380–1100 nm
Camera Weight0.785 kg
Sensor TiltBuilt-in adjustment
PHOTON PLATFORM

Key Imaging Features

Zero Amp-GlowTwo-Stage TEC512 MB DDR3Four-Level Anti-DewIntegrated USB HubSensor Tilt AdjustmentHigh-Speed USB 3.0Short Back-Focus Options
← Back to Photon Series

Technical specification guide

Sensor
Monochrome BSI CMOS
The detector converts incoming light into image data. Sensor type and spectral response must be matched to the observing task.
Resolution
9568 × 6380 (61 MP)
Pixel count describes image dimensions, not optical resolving power. Field coverage and angular sampling also depend on the telescope.
Pixel Size
3.76 μm × 3.76 μm
Physical pixel size combines with focal length to set angular sampling. Choose it together with the optics and typical observing conditions.
ADC
16-bit
ADC bit depth describes digital conversion levels. It is not by itself a measurement of usable dynamic range or sensitivity.
Full Well
51 ke⁻ (111 ke⁻ in LCG)
Full-well capacity concerns the charge stored before saturation. Imaging and gain modes can change the balance between headroom and read noise.
Read Noise
2.8–0.97 e⁻ (LCG) / 1.95–0.9 e⁻ (HCG)
Read noise describes uncertainty introduced during readout. Values depend on gain and operating mode; compare them under equivalent conditions.
Data Interface
USB 3.0 / USB 2.0
Confirm cable, host interface and software compatibility. Transfer performance depends on the complete connection and acquisition settings.
DDR3 Buffer
512 MB
Onboard memory helps manage transfer between acquisition and the host computer. It does not replace adequate host storage and connection bandwidth.
Cooling
Two-stage TEC, up to Δ40°C below ambient
A below-ambient cooling figure describes a temperature difference, not a guaranteed absolute sensor temperature in all conditions.
MODEL TECHNICAL GRAPHICS

Imaging format at a glance

This visual summarizes the published pixel array, pixel pitch and cooling entry for this model. Readout speed, output depth, cooling and spectral response remain configuration-specific; use the technical table above for the full values.

Active pixel array

9 568 × 6 380 px · calculated pixel count 61.04 MP

Calculated pixel count61.04 MP · 9 568 × 6 380 px
Scale: 0–100 MP
Pixel pitch3.76 μm
Scale: 0–10 μm
Cooling differentialup to 40 °C
Scale: 0–50 °C
Spectral response380–1100 nm
Published band for this configuration

How to read these specifications

Pixel count describes the number of image samples; pixel pitch describes their spacing on the imaging plane. Neither value alone determines optical detail or sensitivity. Match sampling to the lens or telescope, field of view, exposure time and acquisition mode. Cooling differential is the stated maximum below ambient when published; it is not a guaranteed operating temperature.

Documentation & compatibility

For Photon 62M, include the intended configuration and application when requesting documentation, compatibility, current availability and lead time.

Photon 62M questions

What is the sensor specification for Photon 62M?

Monochrome BSI CMOS

What is the resolution specification for Photon 62M?

9568 × 6380 (61 MP)

What is the data interface specification for Photon 62M?

USB 3.0 / USB 2.0

Content reviewed .