CELESTRA
CELESTRA VISION SERIES · MONO

Vision 432M

Large-pixel cooled monochrome camera for high-sensitivity deep-sky and narrowband imaging.

CELESTRA Vision series camera illustration
Vision family illustration; model-specific connector layout may differ.
1.76 MP1600 × 1100
9 μmPIXEL SIZE
1.1-inch17.5 mm DIAGONAL
12-bitADC
SENSOR & IMAGING

Mono CMOS

Vision 432M uses the Mono CMOS with 1600 × 1100 active pixels, 9 μm square pixels and an imaging area of 14.4 × 9.9 mm.

The listed ADC is 12-bit. Readout and gain information: As low as 2.4 e⁻. Full-well or imaging-mode information: HCG / LCG operation. These specifications refer to different aspects of acquisition and should be compared in the same operating mode.

COOLING & STABILITY

Built for Long Exposures

A two-stage TEC system with controllable fan can cool the sensor by up to 42°C below ambient during long exposures, with precise temperature regulation for repeatable calibration.

The protection window incorporates software-controlled anti-dew heating. A 512 MB DDR3 buffer supports stable image transfer during long imaging sessions.

9 μmPIXEL SIZE
12-bitADC
512 MBDDR3 BUFFER
ΔT 42°CTEC COOLING
1 HourMAX EXPOSURE
TECHNICAL SPECIFICATIONS

Camera Parameters

Sensor Mono CMOS
Resolution1600 × 1100 (1.76 MP)
Pixel Size9 μm × 9 μm
Image Area14.4 × 9.9 mm
Diagonal / Format17.5 mm / 1.1-inch
ADC12-bit
Read Noise / GainAs low as 2.4 e⁻
Full Well / Imaging ModeHCG / LCG operation
DDR3 Buffer512 MB (4 Gb)
Maximum ExposureUp to 3600 s (1 hour)
INTERFACES & OPERATION

Integration

InterfaceUSB 3.0 / USB 2.0
PowerExternal 11–14 V DC supply
CoolingTwo-stage TEC; up to 42°C below ambient
Temperature ControlPrecision regulated cooling
Anti-DewProtection-window heater, 4 adjustable levels
Readout Performance109 fps at 12-bit; 1600 × 1100 over USB 3.0
Imaging TypeMonochrome / broadband / narrowband imaging
VISION PLATFORM

Key Imaging Features

Large 9 μm PixelsHCG / LCGMono / Narrowband512 MB DDR3Two-Stage TEC ΔT 42°CUp to 1 Hour ExposureUSB 3.0 / USB 2.04-Level Anti-Dew Heating
← Back to Vision Series

Technical specification guide

Sensor
Mono CMOS
The detector converts incoming light into image data. Sensor type and spectral response must be matched to the observing task.
Resolution
1600 × 1100 (1.76 MP)
Pixel count describes image dimensions, not optical resolving power. Field coverage and angular sampling also depend on the telescope.
Pixel Size
9 μm × 9 μm
Physical pixel size combines with focal length to set angular sampling. Choose it together with the optics and typical observing conditions.
Image Area
14.4 × 9.9 mm
The active sensor dimensions determine field coverage together with the optical system. Check that the illuminated field covers the sensor.
Diagonal / Format
17.5 mm / 1.1-inch
Sensor format and diagonal help assess optical coverage and mechanical compatibility; they do not specify the telescope field on their own.
ADC
12-bit
ADC bit depth describes digital conversion levels. It is not by itself a measurement of usable dynamic range or sensitivity.
Read Noise / Gain
As low as 2.4 e⁻
Read noise describes uncertainty introduced during readout. Values depend on gain and operating mode; compare them under equivalent conditions.
Full Well / Imaging Mode
HCG / LCG operation
Full-well capacity concerns the charge stored before saturation. Imaging and gain modes can change the balance between headroom and read noise.
DDR3 Buffer
512 MB (4 Gb)
Onboard memory helps manage transfer between acquisition and the host computer. It does not replace adequate host storage and connection bandwidth.
Maximum Exposure
Up to 3600 s (1 hour)
The listed maximum is an acquisition limit, not a recommended exposure for every target. Sky brightness, saturation and tracking also constrain exposure.
Interface
USB 3.0 / USB 2.0
Confirm cable, host interface and software compatibility. Transfer performance depends on the complete connection and acquisition settings.
Power
External 11–14 V DC supply
Match the external supply to the stated voltage range and confirmed current requirements. Do not infer a current rating from voltage alone.
Cooling
Two-stage TEC; up to 42°C below ambient
A below-ambient cooling figure describes a temperature difference, not a guaranteed absolute sensor temperature in all conditions.
Temperature Control
Precision regulated cooling
Regulated temperature helps make calibration repeatable. Keep acquisition and calibration settings consistent.
Anti-Dew
Protection-window heater, 4 adjustable levels
Window heating helps manage condensation. Choose settings for the local conditions and follow the instrument operating instructions.
Readout Performance
109 fps at 12-bit; 1600 × 1100 over USB 3.0
Readout performance varies with resolution, mode, exposure and host connection. Request mode-specific timing when cadence matters.
Imaging Type
Monochrome / broadband / narrowband imaging
Color and monochrome acquisition use different filter and processing workflows. Choose the type for your target and observing method.
MODEL TECHNICAL GRAPHICS

Imaging format at a glance

This visual summarizes the published pixel array, pixel pitch and cooling entry for this model. Readout speed, output depth, cooling and spectral response remain configuration-specific; use the technical table above for the full values.

Active pixel array

1 600 × 1 100 px · calculated pixel count 1.76 MP

Calculated pixel count1.76 MP · 1 600 × 1 100 px
Scale: 0–100 MP
Pixel pitch9.0 μm
Scale: 0–10 μm
Cooling differentialup to 42 °C
Scale: 0–50 °C

How to read these specifications

Pixel count describes the number of image samples; pixel pitch describes their spacing on the imaging plane. Neither value alone determines optical detail or sensitivity. Match sampling to the lens or telescope, field of view, exposure time and acquisition mode. Cooling differential is the stated maximum below ambient when published; it is not a guaranteed operating temperature.

Documentation & compatibility

For Vision 432M, include the intended configuration and application when requesting documentation, compatibility, current availability and lead time.

Vision 432M questions

What is the sensor specification for Vision 432M?

Mono CMOS

What is the resolution specification for Vision 432M?

1600 × 1100 (1.76 MP)

What is the power specification for Vision 432M?

External 11–14 V DC supply

Content reviewed .