CELESTRA
CELESTRA VISION SERIES · COLOR

Vision 585C

Cooled color camera with HDR, zero amp-glow and enhanced low-light performance.

CELESTRA Vision series camera illustration
Vision family illustration; model-specific connector layout may differ.
3856 × 2180COLOR READOUT
2.9 μmPIXEL SIZE
1/1.2-inch12.85 mm DIAGONAL
12-bit / 16-bit HDRADC
SENSOR & IMAGING

Color CMOS

Vision 585C uses the Color CMOS with 3856 × 2180 active pixels, 2.9 μm square pixels and an imaging area of 11.18 × 6.32 mm.

The listed ADC is 12-bit / 16-bit HDR. Readout and gain information: Ultra-low noise architecture. Full-well or imaging-mode information: HDR / HCG / LCG modes. These specifications refer to different aspects of acquisition and should be compared in the same operating mode.

COOLING & STABILITY

Built for Long Exposures

A two-stage TEC system with controllable fan can cool the sensor by up to 45°C below ambient during long exposures, with precise temperature regulation for repeatable calibration.

The protection window incorporates software-controlled anti-dew heating. A 512 MB DDR3 buffer supports stable image transfer during long imaging sessions.

2.9 μmPIXEL SIZE
12-bit / 16-bit HDRADC
512 MBDDR3 BUFFER
ΔT 45°CTEC COOLING
1 HourMAX EXPOSURE
TECHNICAL SPECIFICATIONS

Camera Parameters

The current color-camera product reference lists 3856 × 2180, while the source technical manual documents 3840 × 2160. These are different documented readouts; confirm the supplied hardware and acquisition mode when selecting a driver profile. The mono model is specified separately. Manufacturer product reference.

Source manual readout reference

Sensor Color CMOS
Resolution3856 × 2180 (listed color readout)
Pixel Size2.9 μm × 2.9 μm
Image Area11.18 × 6.32 mm
Diagonal / Format12.85 mm / 1/1.2-inch
ADC12-bit / 16-bit HDR
Read Noise / GainUltra-low noise architecture
Full Well / Imaging ModeHDR / HCG / LCG modes
DDR3 Buffer512 MB (4 Gb)
Maximum ExposureUp to 3600 s (1 hour)
INTERFACES & OPERATION

Integration

InterfaceUSB 3.0 / USB 2.0
PowerExternal 11–14 V DC supply
CoolingTwo-stage TEC; up to 45°C below ambient
Temperature ControlPrecision regulated cooling
Anti-DewProtection-window heater, 4 adjustable levels
Readout PerformanceHigh-speed USB 3.0 readout
Imaging TypeColor deep-sky imaging
VISION PLATFORM

Key Imaging Features

Enhanced low-light imagingZero Amp-GlowHDR Mode512 MB DDR3Two-Stage TEC ΔT 45°CUp to 1 Hour ExposureUSB 3.0 / USB 2.04-Level Anti-Dew Heating
← Back to Vision Series

Technical specification guide

Sensor
Color CMOS
The detector converts incoming light into image data. Sensor type and spectral response must be matched to the observing task.
Resolution
3856 × 2180 (listed color readout)
Pixel count describes image dimensions, not optical resolving power. Field coverage and angular sampling also depend on the telescope.
Pixel Size
2.9 μm × 2.9 μm
Physical pixel size combines with focal length to set angular sampling. Choose it together with the optics and typical observing conditions.
Image Area
11.18 × 6.32 mm
The active sensor dimensions determine field coverage together with the optical system. Check that the illuminated field covers the sensor.
Diagonal / Format
12.85 mm / 1/1.2-inch
Sensor format and diagonal help assess optical coverage and mechanical compatibility; they do not specify the telescope field on their own.
ADC
12-bit / 16-bit HDR
ADC bit depth describes digital conversion levels. It is not by itself a measurement of usable dynamic range or sensitivity.
Read Noise / Gain
Ultra-low noise architecture
Read noise describes uncertainty introduced during readout. Values depend on gain and operating mode; compare them under equivalent conditions.
Full Well / Imaging Mode
HDR / HCG / LCG modes
Full-well capacity concerns the charge stored before saturation. Imaging and gain modes can change the balance between headroom and read noise.
DDR3 Buffer
512 MB (4 Gb)
Onboard memory helps manage transfer between acquisition and the host computer. It does not replace adequate host storage and connection bandwidth.
Maximum Exposure
Up to 3600 s (1 hour)
The listed maximum is an acquisition limit, not a recommended exposure for every target. Sky brightness, saturation and tracking also constrain exposure.
Interface
USB 3.0 / USB 2.0
Confirm cable, host interface and software compatibility. Transfer performance depends on the complete connection and acquisition settings.
Power
External 11–14 V DC supply
Match the external supply to the stated voltage range and confirmed current requirements. Do not infer a current rating from voltage alone.
Cooling
Two-stage TEC; up to 45°C below ambient
A below-ambient cooling figure describes a temperature difference, not a guaranteed absolute sensor temperature in all conditions.
Temperature Control
Precision regulated cooling
Regulated temperature helps make calibration repeatable. Keep acquisition and calibration settings consistent.
Anti-Dew
Protection-window heater, 4 adjustable levels
Window heating helps manage condensation. Choose settings for the local conditions and follow the instrument operating instructions.
Readout Performance
High-speed USB 3.0 readout
Readout performance varies with resolution, mode, exposure and host connection. Request mode-specific timing when cadence matters.
Imaging Type
Color deep-sky imaging
Color and monochrome acquisition use different filter and processing workflows. Choose the type for your target and observing method.
MODEL TECHNICAL GRAPHICS

Imaging format at a glance

This visual summarizes the published pixel array, pixel pitch and cooling entry for this model. Readout speed, output depth, cooling and spectral response remain configuration-specific; use the technical table above for the full values.

Active pixel array

3 856 × 2 180 px · calculated pixel count 8.41 MP

Calculated pixel count8.41 MP · 3 856 × 2 180 px
Scale: 0–100 MP
Pixel pitch2.9 μm
Scale: 0–10 μm
Cooling differentialup to 45 °C
Scale: 0–50 °C

How to read these specifications

Pixel count describes the number of image samples; pixel pitch describes their spacing on the imaging plane. Neither value alone determines optical detail or sensitivity. Match sampling to the lens or telescope, field of view, exposure time and acquisition mode. Cooling differential is the stated maximum below ambient when published; it is not a guaranteed operating temperature.

Documentation & compatibility

For Vision 585C, include the intended configuration and application when requesting documentation, compatibility, current availability and lead time.

Vision 585C questions

What is the sensor specification for Vision 585C?

Color CMOS

What is the resolution specification for Vision 585C?

3856 × 2180 (listed color readout)

What is the power specification for Vision 585C?

External 11–14 V DC supply

Content reviewed .